Join Today













Site Sponsor
Page 1 of 5 12345 LastLast
Results 1 to 6 of 26
  1. #1
    Premium Member Pac3comm1's Avatar
    Join Date
    May 2010
    Location
    Atlanta Ga
    Posts
    748
    Rep Power
    730

    Default Flash Sprint Touch Pro 2 to Metro PCS, talk, text, web,mms

    Start by downloading these tools:
    Arcsoft MMS cab
    [hide-thanks]
    [Only registered and activated users can see links. ]
    [/hide-thanks]
    Resco Explorer
    [hide-thanks]
    [Only registered and activated users can see links. ]
    [/hide-thanks]
    Resco Registry
    [hide-thanks]
    [Only registered and activated users can see links. ]
    [/hide-thanks]
    Task Manager
    [hide-thanks]
    [Only registered and activated users can see links. ]
    [/hide-thanks]



    *edit* (remember to flash talk and text before this and zero-out the spc)

    1) Run RhodiumW's HardSPL Unlock, while the phone is connected to activesync. After the rom was updated successfully go to step 2

    2)Load this ROM (courtesy of Mighty Mike At PPCG)
    [hide-thanks]
    [Only registered and activated users can see links. ]
    [/hide-thanks]

    3) Install cab listed above and install via active sync. Copy them to a folder that isnt used for anything else so they are easy to locate.

    4)Open Task Mgr. and locate the CM_Guardian file. Kill it.

    5)Open Resco Reg. Exp. and use binocular search (located at the bottom of screen to search for CM_Guardian in registry. Once located,
    select up (located in lower left hand part of screen to navigate to the entire CM_Guardian folder. Press and hold until actions menu appears.
    Select actions and select delete all.

    6)WAP

    A: Goto settings -> Connections -> Connections
    B: Remove any connections that are there
    C: Open your phone and enter ##778#, select "EDIT" and enter your unlock code.

    D: Set the following values:

    M.IP Settings:
    MIP_MODE = Simple IP Only

    M.IP Default Profile:
    NAI = [Only registered and activated users can see links. ]
    Home Address = 0.0.0.0 (just delete the values and save)
    Primary HA Address = 0.0.0.0 (just delete the values and save)
    Secondary HA Address = 0.0.0.0 (just delete the values and save)

    Security:
    HDR AN AUTH User Id = [Only registered and activated users can see links. ]
    PPP USER ID = [Only registered and activated users can see links. ]
    PPP PASSWORD = metropcs

    E: Goto Connections and delete any existing connections and setup a new one using the following settings:

    Number to dail = #777
    Username: [Only registered and activated users can see links. ]
    Password: metropcs
    Domain: (Leave Blank)

    Select Proxy Settings and enter the following values:
    wap.metropcs.net port:3128 (http)
    wap.metropcs.net port:3128 (wap)
    wap.metropcs.net port:443 (secure wap)
    wap.metropcs.net port:3128 (socks)

    F: Back in the "Connections" screen where you have two tabs at the bottom of the screen of "Tasks" and "Advanced", go to Advanced, click on "Select Networks" and select the name of the connection you just setup.

    Example if you leave as Sprint then choose that one as your internet connection and do it for both settings.

    MMS

    MAKE SURE YOUR WEB IS WORKING PROPERLY (ABOVE INSTRUCTIONS) AS YOU CAN'T HAVE MMS WITHOUT WORKING INTERNET!!!!!

    Remove/Uninstall any existing MMS composer you have attempted to setup. Also a good idea to remove any registry keys it may have created that are left behind after the uninstall.

    1: Install Arcsoft MMS version 5.0.70.24 from Verzion.

    2: Open your Messaging and click on the SMS/MMS option.

    3: Click on "Menu" and select "MMS Options" then select the "Servers" tab.

    4: Add a new server with the following settings:

    Server Name: metropcs
    Gateway: wap.metropcs.net
    Port number: 3128
    Server address: [Only registered and activated users can see links. ]
    Connect via: SELECT EITHER THE CONNECTION YOU SETUP ABOVE OR "The internet"
    Send limit: 399K

    5: Click "Done" and then set the new server as default.

    6: Using a Registry Editor edit the following values:

    [HKEY_LOCAL_MACHINE\SOFTWARE\Arcsoft\ArcSoft MMS UA\Config\mm1\WspHeader]

    DELETE KEY -> "X-VzW-MDN"
    ADD STRING -> "X-metropcs-MDN"="XXXXXXXXXX" ( Insert your 10 digit phone Number )
    ADD STRING -> "X-DEVICE-MIN"="1XXXXXXXXXX" ( Insert your 10 digit phone Number WITH the 1 in front of it )

    7)When that is completed successfully type in ##diag# (##3424#) to put the phone in diag mode.

    8)Load the prl with CDMA workshop. If u have the new 3.5 version u can read by HTC METHOD and the spc pops up.

    9)Good Luck. If anything is missing let me know and i will edit.
    Last edited by Pac3comm1; 08-30-2010 at 03:31 AM.

  2. #2
    Apprentice tonasoledad's Avatar
    Join Date
    May 2010
    Posts
    88
    Rep Power
    98

    Default

    just to let people now this will allso work with cricket if u put the righ setting

    GREAT POST MAN

  3. #3
    Newb
    Join Date
    Aug 2010
    Posts
    2
    Rep Power
    0

    Cool tp2

    thanks brothers

  4. #4
    Premium Member Pac3comm1's Avatar
    Join Date
    May 2010
    Location
    Atlanta Ga
    Posts
    748
    Rep Power
    730

    Default

    You re welcome but for future reference, please do not take up thread space to say thanks, please use the thanks buttons.

  5. #5
    Newb
    Join Date
    Oct 2010
    Posts
    3
    Rep Power
    0

    Default

    Does this method work with CDMA workshop 2.7? Also, could you elaborate step 8 of loading the PRL? I don't quite understand! Appreciate it.
    Last edited by dumdedumda; 10-10-2010 at 12:21 AM.

  6. #6
    ?LOST? whitey10tc's Avatar
    Join Date
    Jan 2010
    Location
    Sandy, Utah, United States
    Age
    49
    Posts
    1,701
    Rep Power
    878

    Default

    Quote Originally Posted by dumdedumda View Post
    Does this method work with CDMA workshop 2.7? Also, could you elaborate step 8 of loading the PRL? I don't quite understand! Appreciate it.
    8)Load the prl with CDMA workshop. If u have the new 3.5 version u can read by HTC METHOD and the spc pops up.
    It should work using 2.7 if you follow the tutorial the only real thing your using WS for is to load the PRL. To do so connect to WS and send the SPC then goto the other tab and choose write in the PRL field and select your PRL and click OK.


 
Page 1 of 5 12345 LastLast

Similar Threads

  1. Droid 2 Simple Talk and Text flash to cricket
    By Denver in forum [cricket] Motorola Droid II (2)
    Replies: 11
    Last Post: 03-08-2011, 02:31 AM
  2. Hero full flash (talk text,web,mms,marketplace)
    By johnnyboy14981 in forum [cricket] HTC Hero
    Replies: 0
    Last Post: 07-02-2010, 08:37 PM
  3. Replies: 3
    Last Post: 06-10-2010, 05:07 AM
  4. Moto Droid talk and text flash
    By bigglou23 in forum [cricket] Droid
    Replies: 2
    Last Post: 02-10-2010, 01:32 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •