Flash Sprint Touch Pro 2 to Metro PCS, talk, text, web,mms

[Pac3comm1]

Start by downloading these tools:
Arcsoft MMS cab
[hide-thanks]
[Only registered and activated users can see links. ]
[/hide-thanks]
Resco Explorer
[hide-thanks]
[Only registered and activated users can see links. ]
[/hide-thanks]
Resco Registry
[hide-thanks]
[Only registered and activated users can see links. ]
[/hide-thanks]
Task Manager
[hide-thanks]
[Only registered and activated users can see links. ]
[/hide-thanks]



*edit* (remember to flash talk and text before this and zero-out the spc)

1) Run RhodiumW's HardSPL Unlock, while the phone is connected to activesync. After the rom was updated successfully go to step 2

2)Load this ROM (courtesy of Mighty Mike At PPCG)
[hide-thanks]
[Only registered and activated users can see links. ]
[/hide-thanks]

3) Install cab listed above and install via active sync. Copy them to a folder that isnt used for anything else so they are easy to locate.

4)Open Task Mgr. and locate the CM_Guardian file. Kill it.

5)Open Resco Reg. Exp. and use binocular search (located at the bottom of screen to search for CM_Guardian in registry. Once located,
select up (located in lower left hand part of screen to navigate to the entire CM_Guardian folder. Press and hold until actions menu appears.
Select actions and select delete all.

6)WAP

A: Goto settings -> Connections -> Connections
B: Remove any connections that are there
C: Open your phone and enter ##778#, select "EDIT" and enter your unlock code.

D: Set the following values:

M.IP Settings:
MIP_MODE = Simple IP Only

M.IP Default Profile:
NAI = [Only registered and activated users can see links. ]
Home Address = 0.0.0.0 (just delete the values and save)
Primary HA Address = 0.0.0.0 (just delete the values and save)
Secondary HA Address = 0.0.0.0 (just delete the values and save)

Security:
HDR AN AUTH User Id = [Only registered and activated users can see links. ]
PPP USER ID = [Only registered and activated users can see links. ]
PPP PASSWORD = metropcs

E: Goto Connections and delete any existing connections and setup a new one using the following settings:

Number to dail = #777
Username: [Only registered and activated users can see links. ]
Password: metropcs
Domain: (Leave Blank)

Select Proxy Settings and enter the following values:
wap.metropcs.net port:3128 (http)
wap.metropcs.net port:3128 (wap)
wap.metropcs.net port:443 (secure wap)
wap.metropcs.net port:3128 (socks)

F: Back in the "Connections" screen where you have two tabs at the bottom of the screen of "Tasks" and "Advanced", go to Advanced, click on "Select Networks" and select the name of the connection you just setup.

Example if you leave as Sprint then choose that one as your internet connection and do it for both settings.

MMS

MAKE SURE YOUR WEB IS WORKING PROPERLY (ABOVE INSTRUCTIONS) AS YOU CAN'T HAVE MMS WITHOUT WORKING INTERNET!!!!!

Remove/Uninstall any existing MMS composer you have attempted to setup. Also a good idea to remove any registry keys it may have created that are left behind after the uninstall.

1: Install Arcsoft MMS version 5.0.70.24 from Verzion.

2: Open your Messaging and click on the SMS/MMS option.

3: Click on "Menu" and select "MMS Options" then select the "Servers" tab.

4: Add a new server with the following settings:

Server Name: metropcs
Gateway: wap.metropcs.net
Port number: 3128
Server address: [Only registered and activated users can see links. ]
Connect via: SELECT EITHER THE CONNECTION YOU SETUP ABOVE OR "The internet"
Send limit: 399K

5: Click "Done" and then set the new server as default.

6: Using a Registry Editor edit the following values:

[HKEY_LOCAL_MACHINE\SOFTWARE\Arcsoft\ArcSoft MMS UA\Config\mm1\WspHeader]

DELETE KEY -> "X-VzW-MDN"
ADD STRING -> "X-metropcs-MDN"="XXXXXXXXXX" ( Insert your 10 digit phone Number )
ADD STRING -> "X-DEVICE-MIN"="1XXXXXXXXXX" ( Insert your 10 digit phone Number WITH the 1 in front of it )

7)When that is completed successfully type in ##diag# (##3424#) to put the phone in diag mode.

8)Load the prl with CDMA workshop. If u have the new 3.5 version u can read by HTC METHOD and the spc pops up.

9)Good Luck. If anything is missing let me know and i will edit.

[tonasoledad]

just to let people now this will allso work with cricket if u put the righ setting

GREAT POST MAN

[badboy222]

thanks brothers

[Pac3comm1]

You re welcome but for future reference, please do not take up thread space to say thanks, please use the thanks buttons.

[dumdedumda]

Does this method work with CDMA workshop 2.7? Also, could you elaborate step 8 of loading the PRL? I don't quite understand! Appreciate it.

[whitey10tc]

Does this method work with CDMA workshop 2.7? Also, could you elaborate step 8 of loading the PRL? I don't quite understand! Appreciate it.

8)Load the prl with CDMA workshop. If u have the new 3.5 version u can read by HTC METHOD and the spc pops up.

It should work using 2.7 if you follow the tutorial the only real thing your using WS for is to load the PRL. To do so connect to WS and send the SPC then goto the other tab and choose write in the PRL field and select your PRL and click OK.