HOW TO Flash HTC Imagio to Metro PCS

[Pac3comm1]

I have not been able to find any tutorials anywhere for this device so I will put one here. This is a confirmed tutorial as I have done three today myself. It is very similar to any other HTC except I use a different method for CM Guardian issues. For those who dont know what a CM Guardian file is, it is an .exe that runs in the background and does absolutely nothing until you edit EVDO settings. Soon as you finish it will come right behind you and revert them back to factory settings. We ll get to that later... Lets start here.
Download and install all of these components:
[hide-thanks]
[Only registered and activated users can see links. ]
Arcsoft MMS cab
[Only registered and activated users can see links. ]
Resco Explorer
[Only registered and activated users can see links. ]
Resco registry explorer
[Only registered and activated users can see links. ]
[/hide-thanks]



1. After your devices ESN has been added to the Metro inventory, plug phone in and dial ##3424 then send. This will put the device into DIAG mode. Confirm diag mode by seeing a whitescreen with Tx and Rx and numbers on it.

2. Then open CDMA workshop and click the port button. Select the port that shows Diagnostic. Finally connect and read. Phone should appear on the left of the program if your phone is connected. Once connected, go to the security tab and send 000000 on the SPC to unlock.

3. Now that you are unlocked you can go to PRL tab and load your metro PRL, edit your nam settings,i.e MIN, MDN, SID. On your EVDO tab I would recommend using the MSL code for the password instead of "metropcs". Metropcs still works but more and more people are having to get their pw changed so its better to use the phones MSL. If you need the MSL, go to Whiterabbit.org and enter your ESN/MEID and calculate. It will generate a six digit code for you that you will use for the password. Your EVDO fields should look like this when you are finished.

PPP user: [Only registered and activated users can see links. ]
PPPpass: your six digit MSL
HDR user:yourtendigitnumber@mymetropcs.com
HDRpass: your six digit MSL

If you would like to set up for tethering as well, just add the same settings in for the PAP and HDR on the other four fields on the right. Also on the EVDO tab, make sure the IP behavior is set to Simple. Once all tabs are edited, go to main tab and select mode button to reset. disconnect phone from usb and manually turn off and on as windows phones will not reset by themselves.

3. Once phone is reset, reconnect to PC and wait for Activesync connects. On activesync select explore. When the explore window opens, copy the files I have included above into the "personal" folder. Once copied, disconnect and go to the personal file you just load the files into and click on each to install.

4. Open the task manager to and look for a running process HTC_CM_Guardian. If it is not present, then its not running currently and you can proceed. If it is running, highlight it and kill task.
Now this is the tricky part. Be very careful when editing the registry. Once the programs above are installed, open the resco registry editor and click the binoculars at the bottom of the screen. When the search menu appears, type in CM Guardian. It will search thru the registry until it is located. Once it is located, on the lower left hand part of the screen you will see the word "up". Press it once and it will take you to the folder list where CM Guardian is located. Press the CM guardian folder until a menu pops up that says actions. Select actions and then delete the entire folder. It should give you the option to "Delete All". Do so. You have now removed .exe that gives you all sorts of trouble when trying to edit.

Finally,
WAP

1: Goto settings -> Connections -> Connections
2: Remove any connections that are there
3: Open your phone and enter ##778#, select "EDIT" and enter your unlock code.

4: Set the following values:

M.IP Settings:
MIP_MODE = Simple IP Only

M.IP Default Profile:
NAI = [Only registered and activated users can see links. ]
Home Address = 0.0.0.0 (just delete the values and save)
Primary HA Address = 0.0.0.0 (just delete the values and save)
Secondary HA Address = 0.0.0.0 (just delete the values and save)

Security:
HDR AN AUTH User Id = [Only registered and activated users can see links. ]
PPP USER ID = [Only registered and activated users can see links. ]
PPP PASSWORD = metropcs

5: Goto Connections and delete any existing connections and setup a new one using the following settings:

Number to dail = #777
Username: [Only registered and activated users can see links. ]
Password: metropcs
Domain: (Leave Blank)

Select Proxy Settings and enter the following values:
wap.metropcs.net port:3128 (http)
wap.metropcs.net port:3128 (wap)
wap.metropcs.net port:443 (secure wap)
wap.metropcs.net port:3128 (socks)

6: Back in the "Connections" screen where you have two tabs at the bottom of the screen of "Tasks" and "Advanced", go to Advanced, click on "Select Networks" and select the name of the connection you just setup.

Example if you leave as Sprint then choose that one as your internet connection and do it for both settings.

MMS

MAKE SURE YOUR WEB IS WORKING PROPERLY (ABOVE INSTRUCTIONS) AS YOU CAN'T HAVE MMS WITHOUT WORKING INTERNET!!!!!

Remove/Uninstall any existing MMS composer you have attempted to setup. Also a good idea to remove any registry keys it may have created that are left behind after the uninstall.

1: Install Arcsoft MMS version 5.0.70.24 from Verzion.

2: Open your Messaging and click on the SMS/MMS option.

3: Click on "Menu" and select "MMS Options" then select the "Servers" tab.

4: Add a new server with the following settings:

Server Name: metropcs
Gateway: wap.metropcs.net
Port number: 3128
Server address: [Only registered and activated users can see links. ]
Connect via: SELECT EITHER THE CONNECTION YOU SETUP ABOVE OR "The internet"
Send limit: 399K

5: Click "Done" and then set the new server as default.

6: Using a Registry Editor edit the following values:

[HKEY_LOCAL_MACHINE\SOFTWARE\Arcsoft\ArcSoft MMS UA\Config\mm1\WspHeader]

DELETE KEY -> "X-VzW-MDN"
ADD STRING -> "X-metropcs-MDN"="XXXXXXXXXX" ( Insert your 10 digit phone Number )
ADD STRING -> "X-DEVICE-MIN"="1XXXXXXXXXX" ( Insert your 10 digit phone Number WITH the 1 in front of it )