Join Today













Site Sponsor

View Poll Results: Do u want me to post more solution

Voters
5. You may not vote on this poll
  • Yes

    5 100.00%
  • No

    0 0%
Results 1 to 6 of 6
  1. #1
    Apprentice parin's Avatar
    Join Date
    Jul 2010
    Posts
    57
    Rep Power
    65

    Default HTC Droid Eris Programming

    U will need the following below softwares for the programming of Droid Eris

    QXDM
    [Only registered and activated users can see links. ]
    [Only registered and activated users can see links. ]


    UNICDMA
    [Only registered and activated users can see links. ]
    [Only registered and activated users can see links. ]
    [Only registered and activated users can see links. ]

    WinHex
    [Only registered and activated users can see links. ]

    QPST
    [Only registered and activated users can see links. ]

    HTC Eris Diagnostic Driver
    [Only registered and activated users can see links. ]

    CW2.7
    [Only registered and activated users can see links. ]



    Connect the phone to Computer & Dial ##3424#
    phone will go to Diagnostic Mode & it will ask to install the diagnostic Drivers
    Manually install the drivers from the location where u have downloaded the drivers

    U need to keep the phone in Diagnostic Mode for Programming

    Now Open QPST & Check the port on which the phone is lying
    I phone is now showing try to Add port


    Open CDMA Work Shop 2.7 Cracked
    Select the port on which phone is connected
    Connect the phone
    Press Read
    Now go to security tab
    Send the spc 000000
    press read button in ESN
    than Select Universal Ram Method from Drop down menu
    Press the write button
    It will ask for 2 option
    Select 2nd one Scan for ESN Adress
    Enter the below location, 1 after 1
    0142-1060
    1075-109c
    10d4-10d5
    While Scanning u will get all the pEsn Locations
    Just Note down all addresses in a paper properly without mistake

    Now open UNI CDMA
    Go to Setup
    Select the port on which phone is lying
    once connected go to
    Memory Tab
    first Scan
    0x00000000 to 0xFFFFFFFF
    lenth bytes 8192
    u will get the readable areas
    while scanning the phone will restart
    after restart cancel the scan

    now scan all the readable areas 1 by 1
    in unicdma memory tab
    in Read memory
    Give starting Address as ur 1st readable area eg: 0x103A000
    lenth as 999999999
    Also scan from 0x01042000 to 999999999 to get more MEID locations
    Save the file for all scanning areas

    My Readable & Unreadable areas are as follows
    READABLE area at 0x0103A000
    Unreadable area at 0x0161A000
    READABLE area at 0x1075C000
    Unreadable area at 0x1078E000
    READABLE area at 0x1082A000
    Unreadable area at 0x10D52000
    READABLE area at 0xC0000000
    Unreadable area at 0xC0D00000

    After u r done with scanning
    Open files one by one in winhex
    Search for HEX Values
    To search Put ur phones MEID in Reverse Ex: if ur MEID is AB CD EF GH IJ KL MN, u should seach for MNKLIJGHEFCDAB
    u will get the locations 1 by 1
    note down locations in paper separately for each scan1

    Now u need to calulate the location for QXDM
    Suppose in 2nd scan u got 2 locations where starting Address was 0x1075C000
    Example: 10D98 & 17988
    U need to Add this location with starting Address to get the QXDM Location
    for this u need hex calculator
    10D98 + 1075C000 = 1076cd98 <== This is the location in QXDM were MEID is located
    17988 + 1075C000 = 10773988 <== This is the location in QXDM were MEID is located

    By above calculation u will get all MEID Locations in QXDM

    Now After u have All
    MEID & pEsn Location
    u can proceed to QXDM

    Open QXDM
    Go to COmmunication, Select the port
    Now in Command Line Type
    mode offline-d
    than
    spc "000000"

    Now press F4
    memeory viwer will open

    1st start putting the address u got for MEID
    Exapmple 0x1076cd98 & press Enter
    now u will get ur MEID 14digit in reverse
    make it zero & press write

    After u have made MEID zero

    proceed in same manner for ESN location
    & make it zero

    Now after MEID & ESN has been made zero
    u can confirm it by putting the command
    requestnvitemread esn (for esn)
    requestnvitemread meid (for meid)

    after u get a message that it's zero than u can proceed to write ur ESN or MEID which ever u want

    Commands are
    requestnvitemwrite scm 0x2a

    requestnvitemwrite esn 0xUR ESN
    esn= actual 8 digit esn (not in reverse)

    if u are writing MEID no need to write the esn
    requestnvitemwrite meid 0xUR MEID
    MEID = actual 14 digit meid (not in reverse)

    Restart ur phone, hope ur ESN would have changed

    Now upload the PRL file of desired operator

    For Me MEID Locations were as below on 2.1 official ROM
    0X1076CD98
    0X10773988
    0X10778118
    0X109AD3B4
    0X1083AD98
    0X10841988
    0X10846118
    0X0142AE3C
    0X0142AE48
    0X015CF466


    On Stock 1.5 My MEID locations were
    MEID

    0x01421A1C
    0x01421A28
    0x015B38A6
    0x015B38DC
    0x1076A798
    0x10771388
    0x10775B10
    0x108BFAEC
    0x109AAC2C

    0x1076B388
    0x1076FB10

    U can try above MEID Locations if u dont want to scan

    Good Luck
    Enjoy

    Credits to Hitesh, Gaurav & Tushar for guiding me through the whole process

  2. #2
    ?LOST? whitey10tc's Avatar
    Join Date
    Jan 2010
    Location
    Sandy, Utah, United States
    Age
    49
    Posts
    1,701
    Rep Power
    878

    Default

    Please read the sticky in this forum and all forums before posting. Thread closed.

  3. #3
    Newb
    Join Date
    Apr 2011
    Posts
    2
    Rep Power
    0

    Post Re: HTC Droid Eris Programming

    I can't figure out how to install the diagnostic driver. Can you help me? I am pretty new at this.

  4. #4
    Apprentice
    Join Date
    Jul 2010
    Posts
    66
    Rep Power
    59

    Default Re: HTC Droid Eris Programming

    Quote Originally Posted by mramike View Post
    I can't figure out how to install the diagnostic driver. Can you help me? I am pretty new at this.
    What operating system are you using?

  5. #5
    Newb
    Join Date
    Apr 2011
    Posts
    2
    Rep Power
    0

    Default Re: HTC Droid Eris Programming

    just need to figure out how to switch my sprint lg rumor touch MEID code over to my (non active) verizon HTC eris. everything else is done (prl, and phone number) just need to figure how to get this to work out right. i got most of the codes off, all esn codes are off just need to figure out how to program the MEID in.

  6. #6
    ?LOST? whitey10tc's Avatar
    Join Date
    Jan 2010
    Location
    Sandy, Utah, United States
    Age
    49
    Posts
    1,701
    Rep Power
    878

    Default Re: HTC Droid Eris Programming

    Quote Originally Posted by mramike View Post
    just need to figure out how to switch my sprint lg rumor touch MEID code over to my (non active) verizon HTC eris. everything else is done (prl, and phone number) just need to figure how to get this to work out right. i got most of the codes off, all esn codes are off just need to figure out how to program the MEID in.
    Discussions of cloning an ESN/MEID from one device to another are against the forum rules and also illegal in the USA! For violating the forum rules members receive a 24 hr ban on the first offense. There are no exceptions to this rule and it is here for the protection of the forum and it's members.


 

Similar Threads

  1. roms for droid eris
    By darules0 in forum Flashing Android to Metro PCS
    Replies: 2
    Last Post: 02-10-2011, 11:09 AM
  2. Root a Droid Eris with 2.1 ROM
    By thesmitty68521 in forum [cricKet] HTC Eris
    Replies: 4
    Last Post: 08-10-2010, 04:30 AM
  3. NEW HTC DROID Eris OS 2.1v3 Leaked
    By Genuwine1976 in forum HTC Eris
    Replies: 0
    Last Post: 06-24-2010, 03:22 AM
  4. Droid Eris Talk/Text
    By thesmitty68521 in forum [cricKet] HTC Eris
    Replies: 9
    Last Post: 06-17-2010, 06:50 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •