What is the password?
Credit goes to "zfxp" on [Only registered and activated users can see links. ] For the guide
A guide I used with CDMA WS but you don't have to have it with guide.
First and foremost, you need to have your moment ESN activated on p+
next step, download this prl file, unzip it into a place you'll remember! [Only registered and activated users can see links. ]
Next step download QPST 2.7.323 Google it!!!
Assuming you have all of the samsung drivers for your phone to use as a modem. If not search this forum, you'll find them! Connect your phone, then Settings -> wireless* -> Check Dial-up networking.
Now open "Qpst configuration" then add port, add your port that your phone is connected to.
You'll need your MSL code, to obtain it, download "connectbot" from Marketplace, open connectbot, choose "local" hit enter, then type getprop, and look for "r1l.MSL", the 6-digit number is your MSL.
next step is to enter your MSL on connection to qpst, by selecting your phone in qpst configuration, then hit "start clients" and click "Service programming", then hit okay, then click "Read from phone" then change it by viewing in qpst "service code" change it to 000000. Then proceed to "Roam" and upload the PRL you had previously downloaded at the beggining of the post, then at the bottom right, click "Write to phone"
Your phone will restart, then once your phone has started dial *22890, programming will go through once it's finished restart your phone.
Next step repeat to connect to QPST, goto mip tab edit profile "1" changed NAI and Tether NAI to Yourphonenumber(at)vzw3g.com
Rev Tunnel Preferred: yes
Home address: 0.0.0.0
Primary HA address: 255.255.255.255
Seconday HA address: 255.255.255.255
MN-HA SPI: 12C
MN-AAA SPI: 2
DMU Public Key ID: 10
DMU Mobile Authenticator: (empty)
HA Shared Secret: (empty)
AAA Shared Secret: (empty)
Active User Profile: 1 (this appears to reset to 0 after every write)
Now click the PPP Tab and change AN/UM to Yourphonenumber(at)vzw3g.com and use password "vzw" without th quotes, then go back to MIP tab, and change to Simple IP only.
Then disable EVDO by going to dial pad dialing ##33284#, enter MSL which now should be "000000", hit HDR/1X Selection. Then choose CDMA only Mode hit okay then hit your home button.
Restart and you SHOULD have internet.
MMS! goto dialer, Dial ##DATA# goto MMSC URL, type MSL which should be "000000" at this point, replace your url with "http://mms.vtext.com/servlets/mms" press okay. and hit your home button.
Last edited by 4MUSKRAT; 08-18-2010 at 02:35 PM.
What is the password?
Can i please have the password?
iPhone Moderator, Trusted Guru &
CDMA GURUS Booster
guys you see how old this thread is.lol. just use any vzw prl there are many out there,if the one you use doesnt seem to get good service just try another.but pp=vzw
Custom tools and custom phone & mifi firmwares built to your specs.Contact me !
I WILL NOT ANSWER SUPPORT QUESTIONS THRU PRIVATE MSG.
See mifis.us for unlimited data on vzw-AT&T-TMO-or some MVNO's (Resellers welcome)
www.mifis.us <--get yer unlimited data mifis here
ok can someone tell me what i did wrong. i followed the instructions but when i did the over the air programming the call drops and i have no signal. please some one help.
iPhone Moderator, Trusted Guru &
CDMA GURUS Booster
you need to not only write your prl but your sid also,if you still have the sprint sid,ota wont work.so change it to one of the vzw sid's like 59 or 22 or for that matter you could probly leave it blank,just dont leave the sprint sid in there.
Custom tools and custom phone & mifi firmwares built to your specs.Contact me !
I WILL NOT ANSWER SUPPORT QUESTIONS THRU PRIVATE MSG.
See mifis.us for unlimited data on vzw-AT&T-TMO-or some MVNO's (Resellers welcome)
www.mifis.us <--get yer unlimited data mifis here
Bookmarks