Palm Pre/BB/Hero/Moment and other Smartphone Settings for PP

[meanngreen04]

These have all worked for the Palm Pre, BB, Hero, and Samsung Moment to get full internet on Page Plus. Special thanks to younggunna23 for his helpful post on HoFo.

1) Read phone with Service Programming (QPST)

2) Under MIP tab set phone to SIMPLE IP behavior.

3) Edit Profile 1 (not Profile 0) and only that one. Change the NAI to [Only registered and activated users can see links. ] (sets provisioning)

4)Enable and Edit Profile 2 this is where you input our settings
User Profile 2

Profile Enabled: yes
NAI: [Only registered and activated users can see links. ]
Tethered NAI: [Only registered and activated users can see links. ] (NOTE: This resets to myphonenumber after every write)
Rev Tunnel Preferred: yes
Home address: 0.0.0.0
Primary HA address: 255.255.255.255
Seconday HA address: 255.255.255.255
MN-HA SPI: 12C
MN-AAA SPI: 2
DMU Public Key ID: 10
DMU Mobile Authenticator: (empty)
HA Shared Secret: (empty)
AAA Shared Secret: (empty)
Active User Profile: 2 (this appears to reset to 0 after every write)

5) Go to PPP tab, change username and password to [Only registered and activated users can see links. ] pw vzw for both UM/AN sections
(repeat writes on this may be required for it to stick)

6) Go to ROAM tab, write your PRL..


Obviously, this is not a complete guide just the internet setup to get these phones correctly functioning on PP. With the BB, you will have to have a custom service book. There is a copy of one on HOFO.

[antivirus1]

These have all worked for the Palm Pre, BB, Hero, and Samsung Moment to get full internet on Page Plus. Special thanks to younggunna23 for his helpful post on HoFo.

1) Read phone with Service Programming (QPST)

2) Under MIP tab set phone to SIMPLE IP behavior.

3) Edit Profile 1 (not Profile 0) and only that one. Change the NAI to [Only registered and activated users can see links. ] (sets provisioning)

4)Enable and Edit Profile 2 this is where you input our settings
User Profile 2

Profile Enabled: yes
NAI: [Only registered and activated users can see links. ]
Tethered NAI: [Only registered and activated users can see links. ] (NOTE: This resets to myphonenumber after every write)
Rev Tunnel Preferred: yes
Home address: 0.0.0.0
Primary HA address: 255.255.255.255
Seconday HA address: 255.255.255.255
MN-HA SPI: 12C
MN-AAA SPI: 2
DMU Public Key ID: 10
DMU Mobile Authenticator: (empty)
HA Shared Secret: (empty)
AAA Shared Secret: (empty)
Active User Profile: 2 (this appears to reset to 0 after every write)

5) Go to PPP tab, change username and password to [Only registered and activated users can see links. ] pw vzw for both UM/AN sections
(repeat writes on this may be required for it to stick)

6) Go to ROAM tab, write your PRL..


Obviously, this is not a complete guide just the internet setup to get these phones correctly functioning on PP. With the BB, you will have to have a custom service book. There is a copy of one on HOFO.

did all this and AN sections is resetting.. another thing.. do i put pw vzw in the password section or just vzw..

[rockinmobile]

just put vzw in the password section.

[antivirus1]

Ok.. Did that but UM/AN sections.. AN sections keep resetting but to sprint... one more thing.. where u have [Only registered and activated users can see links. ] i replace myphonenumber with my mobile number... right

[markymark805]

Ok.. Did that but UM/AN sections.. AN sections keep resetting but to sprint... one more thing.. where u have [Only registered and activated users can see links. ] i replace myphonenumber with my mobile number... right

yes, put in your 10 digit number

[steeck1]

no word on the an section reverting back to sprint? I too have the same problem