Treo 800w full flash

[bigglou23]

Treo 800w Full Falsh - Thanks to tonycortes (a.k.a. supernine) for doing this amazing solution.

First you will need to get all of the files from the link below:


[hide-thanks][Only registered and activated users can see links. ][/hide-thanks]


Then just follow the guide that is included with the files. Below is a copy of that guide.

Cricket 800w solution
BY SUPERNINE
Credits: Beezlewaxin for great drivers, Randomwit for great CAB ideas.

0) Before anything, I recommend executing a hard reset to avoid any issues (##RTN#)

1) Place phone in DIAG PASSTHRU by dialing ##3424#

2) Connect phone via USB cable

3) Instal Beezle's Treo DIAG drivers for the new hardware detected: [Only registered and activated users can see links. ]



4) Retrieve SPC from memory read at the following address:
Address: 0x00790000-007A0000

5) After retrieving SPC, set it to zeros using CDMA Workshop. Also load your PRL.

6) Using NV Items Write feature under memory tab, apply the IOTA Bypass (800W_IOTA_Bypass.txt)

7) Then using the Authentication feature under EVDO tab, edit fields to match:

Username: [Only registered and activated users can see links. ]
Password: cricket
IP Behaviour: Simple IP
Active: 0

8) Perform a mode reset, phone will not reboot, just radio.

9) After mode reset, make sure you disable DIAG PASSTHRU and transfer the provided CAB (CKT800W[S9]) via ActiveSync

10) Using File Explorer, launch the CAB, accept any warning or prompts. After it successfully installs, it will ask to reboot device.

11) Once phone is rebooted, your device is ready to use. First time use of WAP will ask for username (phonenumber@mycricket.com) and password (cricket).
And if you wish, remove the Sprint contact in the phonebook.

12) Enjoy the fully flashed phone with EVDO, WAP, and MMS.


Palm Centro IOTA + Provisioning Bypass - Thanks to insanecain for doing this solution. This was a long awaited one for many. All my other carrier
Centro solutions are based off this.

First get the file from the link below:
[Only registered and activated users can see links. ]

Now just use CDMA Workshop to write these nv items to your device under the "Memory" tab.

Next, you will need to make sure that your "NAM" and "EVDO" tabs are programmed correctly.

[pluckyducky]

you can buy the newest version from [Only registered and activated users can see links. ] its like $107. Really useful tool or you can download the crack version 2.7
[Only registered and activated users can see links. ] posted by DEX.

[interceptor93]

Im trying to install the cab to my treo 800w and im keep getting an error that the cab cannot be installed (try installing a different location!!)

What i am doing wrong???

Thank You!!!

[f150xlt]

how can i install the driver to my pc so cdma workshop (2.7) will connect to my treo 800w . when i try to connect my treo 800w to workshop i get phone is not connected to com port or com port dose not exist.

[Wrecked Johnson]

Im trying to install the cab to my treo 800w and im keep getting an error that the cab cannot be installed (try installing a different location!!)

What i am doing wrong???

Thank You!!!

Try installing the cab to the device, if that dont work try the memory card, if that dont work look for a new cab file yours might be corrupt

[Wrecked Johnson]

how can i install the driver to my pc so cdma workshop (2.7) will connect to my treo 800w . when i try to connect my treo 800w to workshop i get phone is not connected to com port or com port dose not exist.

If you already have the drivers for the phone all you need to do is put the phone in diag mode then connect the phone it should look for the drivers right away and you will most likely have to browse to the folder and pick which drivers to install.