w385 spc code

[rlj1117]

i have latest paid version of cdma ws , any body know how to get spc code?

[rich hathaway]

if its postpaid its 000000 if its prepaid just flash it with the w385 monster and it will change spc to 0's for you.

[dilworks]

Or simply use any seem editor to read Seem 0055, Bytes 0006, Record 0001. No need to flash anything :)

IIRC, the W385 should work with P2K05 Seem Editor, which is plug'n'play - plug the phone and it will display the SPC on screen - i did one a long, long time ago...

[rlj1117]

cant get phone to connect to p2k05

[rich hathaway]

sounds like you need the drivers. try the first one. if it doesnt work then use the second one. download and unpack then point your pc to them if it doesnt find them automatically.

[Only registered and activated users can see links]
[Only registered and activated users can see links]

[thesmitty68521]

There might be an all around easier way to do this. What network do you want the phone on? There is a generic for this model out there somewhere. And the generics are always "000000". That would be my suggestion.

[barrios]

here is the firmware generic of motorola w385, i hope is usefull for someone, bye.
[Only registered and activated users can see links]!download|556tl|160489464|DST_W385_FLASH_GENERICA _BY_UNLOCK_CELULAR.rar|21517

[rlj1117]

i used 000000 but that wont correct , when i download generic what do i do with it , the only program i can get to connect to phone is qpst

[123456&]

You need RSD LITE program

[rich hathaway]

here is rsd lite it is easy to use. just make sure to select the file then just press start and give it a few.
this was originally posted by drkcobra


[Only registered and activated users can see links]

[army_one17]

rich hathaway is right, if is the prepaid version just install the correct motorola driver, plug it trough rsd lite, flash it with the w385 verizon monster file and u get 000000 as spc. Take just around 10 mins to get it done.

[rlj1117]

i hope i am not double posting but i dl rsd lite from the above link , loaded w385 generic , and pressed start , is this correct ? , its been running for about 10 mins now , is this normal?

[rich hathaway]

sometimes it will only get to 99% because the software has troubles restarting some phones so you will need to manually power up the phone to finish it.but the time it takes depends on yer pc. around 10 minutes is normal.

[rlj1117]

ok been trying to figure this out , when i look at rsd lite bottom left hand corner it says disconnected , is this a driver issue ? if so how do i get the driver into rsd lite ? thanks

[rlj1117]

ok finally got file wrote to phone , i had to use a comp with xp on it , now phone just flashes a m on the screen , what do i do now

[rich hathaway]

try to pull the battery out and put it back in and hold the # and the * then while holding them push power, that will manually put the phone in bootloader (blue moto screen), then plug the phone open rsd lite,make sure the phone shows up,select the correct monster file and click start. let it run until finished.this should recover your phone. but you have to make sure to use the correct monster file.

[drkcobra]

For the Verizon W385, this would be the correct monster pack:
[Only registered and activated users can see links]

[rlj1117]

is this file for boost ? if not do you have a link , thanks

[rich hathaway]

this is a verizon file. when it say "vzw" it is verizon

here is the boost w385 [hide-thanks] [Only registered and activated users can see links][/hide-thanks]

originaly posted by drkcobra

[berticoit]

I Could change the SPC using P2K05, but still has problem with the configuration. When I try #073887* i get another Security code. There is any way to get it?

Thanks

[drkcobra]

I Could change the SPC using P2K05, but still has problem with the configuration. When I try #073887* i get another Security code. There is any way to get it?

Thanks

You will find the security code located at 2786 (hex), and for reference the lock code is located at 2784.