love2sin
08-26-2010, 11:27 PM
THIS IS FOR METROPCS
Step 1.
Remove your MicroSD card and plug the phone into your PC via USB cable then open QPST (QPST Configuration, then go to Start Clients and select Service Programming) and then read the phone.
[Only registered and activated users can see links]
remove any ip address that you find in these 2 profiles. and remove any other profiles except the first 2.
also make sure both of them say enabled.
Now go to ppp config tab...
[Only registered and activated users can see links]
once you are completed with this make sure you write to the phone and move on to the next step..
Step 2.
click on phone icon (on the phone)
click on the dialer..
enter ##3282#
click user name
click edit
enter your spc which should already be 000000 by now
Here are the settings:
[Only registered and activated users can see links]
SPI MN-HA "1234"
SPI MN-AAA "1234"
M Home Address "000.000.000.000"
Prim Ha Ip "255.255.255.255"
Sec Ha Ip "255.255.255.255"
Rev Tunneling "Off"
AAA Password "MSL"
HA Password "MSL"
click done and allow the phone to reboot...
Step 3.
Now do ##3282# again.. this time go to browser
click edit
enter spc
youll see gateway1 and gateway2, under both of these
you will see primary and secondary,,, set primary and secondary ip`s
for both gateways to 010.223.002.004,, they will all be the same ip address,,
and set the Port 3128 and secure Port 443 for all gatways to ,, hit done and reboot.
Also this should work on quite a few other Sprint phones,,
This is what I do for a living at the wireless company I work for,,
and so far it has worked on Samsung upstage, Instinct,, Sanyo katana, and many others,,,
I have this working on my Instinct and if you have any questions please let me know via this thread.
I got this a while back. I think from HoFo - Credit goes to the HoFo member who wrote this up
ENJOY !!!!!
Step 1.
Remove your MicroSD card and plug the phone into your PC via USB cable then open QPST (QPST Configuration, then go to Start Clients and select Service Programming) and then read the phone.
[Only registered and activated users can see links]
remove any ip address that you find in these 2 profiles. and remove any other profiles except the first 2.
also make sure both of them say enabled.
Now go to ppp config tab...
[Only registered and activated users can see links]
once you are completed with this make sure you write to the phone and move on to the next step..
Step 2.
click on phone icon (on the phone)
click on the dialer..
enter ##3282#
click user name
click edit
enter your spc which should already be 000000 by now
Here are the settings:
[Only registered and activated users can see links]
SPI MN-HA "1234"
SPI MN-AAA "1234"
M Home Address "000.000.000.000"
Prim Ha Ip "255.255.255.255"
Sec Ha Ip "255.255.255.255"
Rev Tunneling "Off"
AAA Password "MSL"
HA Password "MSL"
click done and allow the phone to reboot...
Step 3.
Now do ##3282# again.. this time go to browser
click edit
enter spc
youll see gateway1 and gateway2, under both of these
you will see primary and secondary,,, set primary and secondary ip`s
for both gateways to 010.223.002.004,, they will all be the same ip address,,
and set the Port 3128 and secure Port 443 for all gatways to ,, hit done and reboot.
Also this should work on quite a few other Sprint phones,,
This is what I do for a living at the wireless company I work for,,
and so far it has worked on Samsung upstage, Instinct,, Sanyo katana, and many others,,,
I have this working on my Instinct and if you have any questions please let me know via this thread.
I got this a while back. I think from HoFo - Credit goes to the HoFo member who wrote this up
ENJOY !!!!!