How To Install and Register DLLs for LGNPST

[bigglou23]

Add the LGNPST dll to it and it will tell you what generic model you need, Then register it....enjoy :)

[hide-thanks][Only registered and activated users can see links][/hide-thanks]

**Courtesy of Tony Cortes**

[ownmart]

where does it tell you that?

[bigglou23]

There is a window on the top left, thats where it will show you :)

[k3rrsed]

I probably deserve no credit for anything you read below. But I did write this all up, so give thanks if you deem it appropriate.

Note that you will probably need to install Generic Components for LGNPST.

You will need:

LGNPST Lab Level 1.1
the DLL for the LG device you are flashing
the corresponding generic DLL for the LG device you are flashing
Right_Click_Register_DLL
[Only registered and activated users can see links]

Following is a list of LG devices and their corresponding Generic DLLs:

AX265 1.0.12.0
VX8360 1.0.3.0
VX8550 1.0.3.0
VX8560 1.0.3.0 or 1.0.4.0
VX9100 1.0.1.2
VX9200 2.0.24.0
VX9600 1.0.5.0
VX9700 1.0.2.0
VX10000 1.0.6.0
VX11000 2.0.29.0

The Voyager (VX10000) will be used for the following example.

1. When you are installing DLLs for LGNPST, you should first navigate to C:\LG Electronics\LGNPST and ensure there is a Model folder present. If not, create one.

NOTE: You will want to verify you have LGNPST Lab Level 1.1 or higher installed. LGNPST Store Level will not allow you to NV Read and Write in the same manner as Lab Level.

2. Within the Model directory (the path to which is listed above), create another directory for the model of phone you are attempting to flash. For the Voyager, create a directory titled “VX10000”.

3. Install Right_Click_Register_DLL. Installing this file will allow you to right-click and register the proper DLL without having to use the command line.

4. In the folder you just created in the Model directory, paste the DLL of the LG model you are attempting to flash. For the Voyager, paste the LGNPST_VX10000.dll.

5. In the same folder, paste the generic DLL that corresponds with the LG model you are attempting to flash. For the Voyager, paste the LGNPST_GenericModel_Ver_1_0_6_0.dll.

6. Next, right-click the model DLL (not the generic DLL) and select "Register" from the contextual menu. For the Voyager, right-click the LGNPST_VX10000.dll and select Register from the contextual menu.

You do NOT need to right-click to register the GenericModel DLL. If you successfully registered the DLL, you will see the following (or a similar) message: "DllRegisterServer in C:\LG Electronics\LGNPST\Model\VX10000\LGNPST_VX10000.dl l succeeded".

7. Now open LGNPST. If the “Model” section in the upper left shows UNKNOWN, click File from the menu, Select DLL and choose the proper DLL, in this case the VX1000 DLL. Then close LGNPST and relaunch it. Verify the “Model” section displays the correct model name, in this case VX10000 or VX10K.

You should now have successfully registered your DLL for use with LGNPST!!!

[bhoff]

Great post really appreciate this one fellas. Have a question, i don't understand what the components are for which components do I need if any for 1.1 lab for example?

[Dex]

Here it is for all u VISTA and Windows 7 Users who dont have UAC turned off

Right Click to Register As Administrator ([Only registered and activated users can see links])

[Tannus]

Here it is for all u VISTA and Windows 7 Users who dont have UAC turned off

Right Click to Register As Administrator ([Only registered and activated users can see links])

I didn't have that option till I got UR flash pack 5 DEX.

Thanks 4 that by the way

[Dex]

Your welcome yes its incorp in Flash pack 5 but for those that dont have it there it is

[Tannus]

No I had right click registry. but I didn't have the option 2 (register as administrator) until I got the flash pack 5. It was just register or unregister.

[t1tu]

cant register the dll... the following error comes up [Only registered and activated users can see links] cAAm1T1UGlPLmzgun_tyNXCRAq7bgS4qmAE.jpg

[fr0st]

where does it tell you that?

what do you mean

[brenda]

brenda8/3/10

[whitey10tc]

brenda8/3/10
Brenda please review the posted rules. Thread hijacking is against the forum rules and creates confusion. Your post is just that a hijack, it promotes people to further post things like what do you mean? and takes the thread off topic.

[army_one17]

Here it is for all u VISTA and Windows 7 Users who dont have UAC turned off

Right Click to Register As Administrator ([Only registered and activated users can see links])

thanks buddy for this useful file, i was trying to register my lgnpst dlls on my windows 7 with no luck but reading trought the forum i found this post, worked like a champion, i appreciate u so much.

[antbeze07]

Thanks, this program makes it so easy to register DLLs

[kristina2dope]

ok so i found a link to download generic dlls....but for the vx9100 it says to get generic 1.0.1.2 but i dont see that one anywhere help!

[thesmitty68521]

ok so i found a link to download generic dlls....but for the vx9100 it says to get generic 1.0.1.2 but i dont see that one anywhere help!

Please ask your question one time in one post. You have two different posts asking for the same thing. I am uploading the DLL for you now. I will send you the link. Thanks.

[thesmitty68521]

[Only registered and activated users can see links] is the link for the 9100 DLL

[elisa191]

Hello all,

I am using windows 7 and have used LGNPST for some time with LG phones. I got my fist LG enV 11000 in my shop today and I cant get it recognized in LGNPST. I have followed this forum and others and have the appropriet .dll in a new folder in the model folder in the LGNPST folder on my C: drive but when I try and register the .dll I just keep getting an error that it failed to load. I have tried different .dll downloads and have used the "Run as Admin" approach but to no avail!!!!

I did get the phone out of here by rewirting the cricket nv files to be compatible with Metro and wrote them with CDMA but I love using LGNPST for my LG stuff. If any of you have had this problem and have overcome it please let me know..

Thank you

Elsia

[rich hathaway]

do you have the correct generic in the same model folder, you need - GENERICMODEL_VER_2_0_29_0.dll it is posted here.if you cant find it i will put it up again for you.

[cellfonepimp]

Ive followed k3rresd's directions to the letter, I cant get lab 1.1 to read my lg11000. Is there another way to get this to work?

[123456&]

Ive followed k3rresd's directions to the letter, I cant get lab 1.1 to read my lg11000. Is there another way to get this to work?

Try with LGNPST lab 1.2.

[whitey10tc]

Emergency mode. Then it'll connect also make sure that the USB is set right in ##LGservicemenu, but really this is not really the thread to be asking anything else other than how to register the DLL.

If you need further help try the search feature XV11000 it'll bring up a few other threads that had similar issues and solutions. If you still can't get it start a new thread in the appropriate forum ie. cricket LG, "if flashing to cricket", etc, and I'll throw everything together and post it there tomorrow sometime. I just had one that refused to connect until I downgraded and flashed it in emergency.

[bvr127]

does anyone have the latest componets and versions for lgnpst.... the exact ones i need are LGNPST Component version 5.0.12.0, and the Generic Model version 5.0.10.0

[123456&]

does anyone have the latest componets and versions for lgnpst.... the exact ones i need are LGNPST Component version 5.0.12.0, and the Generic Model version 5.0.10.0
Check this thread ([Only registered and activated users can see links])

[sunnykhona]

Can i get LG RD6100 Lgnpst dll please.....

[Link]

Please excuse my idiocy as I'm only a n00b to this, but I've looked all around and I can't seem to find a solution to registering the AX260 dll. Here's a screenshot of what happens when I try:
[Only registered and activated users can see links] ([Only registered and activated users can see links])

I put IEShims.dll in that folder as the Dependency Walker said it could not find that file. I don't exactly understand the other error: "Warning: At least one module has an unresolved import due to a missing export function in a delay-load dependent module."

Any help is much appreciated and thanks for reading this. :)

[123456&]

You don't need to register that dll, use lgdowload for that model.

[rich hathaway]

use this small software it will help you add these dlls to your registery.unpack it and it will ad it to your right click menu and work with the right click to register softwares.

it works with win7 in most cases,however if you have changed your registry or recently run any registry cleaners or boosters you might have issues,they tend to mess up your registry and make what usually works not work.


[hide-thanks][Only registered and activated users can see links][/hide-thanks]

[Link]

You don't need to register that dll, use lgdowload for that model.

Many thanks; I guess that was obvious, but I didn't know better. >< Anyhow, it's all updated now! :)

[modeso]

thank u for thats

[puckwithahalo]

Check this thread ([Only registered and activated users can see links])

Just out of curiosity, why does that link tell me that I don't have permission to access that page?

[puckwithahalo]

ok, guess no help for the noob...sorry to have bothered.

[captainkirks]

Just out of curiosity, why does that link tell me that I don't have permission to access that page?

I get the same error, I think the link is bad.

[123456&]

Just out of curiosity, why does that link tell me that I don't have permission to access that page?
Sorry, my friend, I think the link was removed By Admins

[whitey10tc]

Check this thread ([Only registered and activated users can see links])


Just out of curiosity, why does that link tell me that I don't have permission to access that page?


ok, guess no help for the noob...sorry to have bothered.


I get the same error, I think the link is bad.


Sorry, my friend, I think the link was removed By AdminsThe link references above, is an expired market place post. Market place posts are only valid for 30 days then they need to be renewed.

[puckwithahalo]

Ok, thanks. Sorry for the grumpy post. I was in a really bad mood, and might have been slightly tipsy too. So yeah, very sorry for the bad form.

[mqa83]

thanks you

[kristina2dope]

i have lgnpst v 1.2 lab will it work with this tutorial? thanks!

[naymsa]

\thank you very much much

[sevenveils]

Thanks a lot for your explanations.

This was a hellacious multi-hour process, but I finally found a working LGNPST DLL installer link for my VX10000 here. <FOREVER in the debt of cdmagurus.com!>

[n1337]

thanks 123456578910245654

[frankerebus]

that work for all models?

[arena22]

Hopefully this will work :3

[LawrenceU]

ive been having challenge registering th vx1100 dll file in my xp system. the file doesnt give me the option to register. i tried using the regsvr32 vx11k.dll but i keep getting response as file loaded but dllserver cannot be found.

Pls kindly assist me

[123456&]

You have to run the Right_Click_Register_DLL file first.. then install the components..once you done that..you can register the dll.

[Pavel1724]

Thanks 123456578910245654

[rockinzogg]

Can you share that link, please. I'm in the middle of working with my VX10000 and could use all help i can get. thanks.

[ELHULK]

IS THERE a new link or can someone provide this please

Here it is for all u VISTA and Windows 7 Users who dont have UAC turned off

Right Click to Register As Administrator

[skyangel12]

Download not available File not found.

- - - Updated - - -

Download not available File not found.

[Colbert87]

Add the LGNPST dll to it and it will tell you what generic model you need, Then register it....enjoy :)

*** hidden content ***

**Courtesy of Tony Cortes**

I cant get my US730_120831.dll to register so i can use it with lgnpst when i right click it and click register i get this message the module C:\users\name\desktop\us730_120831.dll was loaded but the entry point dllregisterserver was not found. make sure that... users\name blah blah is a valid dll or ocx file and then try again

[Colbert87]

and that dll is the only thing im waiting on i have my tot waiting patiently on this dll if i could just get it to register i could click start

- - - Updated - - -

and that dll is the only thing im waiting on i have my tot waiting patiently on this dll if i could just get it to register i could click start

[123456&]

The dll you are trying is not valid to get register, it was made for other tools, like lgdp2 or lgflash etc.

[Colbert87]

The dll you are trying is not valid to get register, it was made for other tools, like lgdp2 or lgflash etc.

well thats fantastic what should i do then

[123456&]

What are you trying to get done?

[Colbert87]

What are you trying to get done?


I cant get my US730_120831.dll to register so i can use it with lgnpst when i right click it and click register i get this message the module C:\users\name\desktop\us730_120831.dll was loaded but the entry point dllregisterserver was not found. make sure that... users\name blah blah is a valid dll or ocx file and then try again...... ive tried thru regsvr32 and about every other way i can think of

[rich hathaway]

he was asking you what your trying to do,as in reload firm or flash,or just what you need to do friend other than register the dll,whats the end result you need.

[Colbert87]

he was asking you what your trying to do,as in reload firm or flash,or just what you need to do friend other than register the dll,whats the end result you need.

my lg splendor is hard bricked its stuck on the lg screen and says download is in progress do not disconnect cable.... so im trying to reflash the stock firmware i suppose ive never used lgnpst i have the tot file i just cant get the dll to register so end result is my phone working again lol or if yall know of another way that isnt this extreme and hard for me to do please let me know lol

[Colbert87]

i guess i should add that i flashed a rom for a optimus l7 by accident and it did this to it and felt so relieved that i found lgnpst and people claim that this fixes it but i cant get the dll to register i can still send it in its still under warranty but id rather learn from mistakes and fix this one so in the future ill know what to do

[123456&]

You won't be able to register that dll bro for that model, You will need to find a crack version of lgdp2 to be able to reload the tot file back to your phone.

[Colbert87]

You won't be able to register that dll bro for that model, You will need to find a crack version of lgdp2 to be able to reload the tot file back to your phone.

thanks man that got it done phone is back to normal

[123456&]

Good to know that you fixed.

[whyrless]

Hey guys had a few questions and needed a little clarification. Im trying to figure out if there is a way to extract the HA and AAA passwords from an LG730 - LG Venice..someone told me that i just needed to unlock the nv folder using LGNPST and of course i then found out that you needed a .dll to communicate with the device..so i found one..but then received an error attempting to register it so i followed that until i found this thread and from what i can understand u cant use LGNPST with the LG Venice..soooo i was wondering if anyone knew a way to read the ha and aaa passwords from the LG Venice - LG730

thanks

[rich hathaway]

use wireless workshop or cdma workshop or one of about 10 other tools that will read nv's.

[whyrless]

Hey Rich, thanks 4 the reply, i actually have cdma ws 3.9...i just activated it this morning, i can connect and read it but i cannot read the ha and aaa passwords and sum1 in another thread on another forum said it was because i needed to unlock the nvitems using LGNPST using the corresponding dll?.....LOL sounded like a starting point to me so i went with it.

[rich hathaway]

do you know which 2 nv items to read?

[whyrless]

not really, i read up on it a little bit last night and they said that the passwords are usually held in 465 466 1192 and 1194 although im not sure. Rich can i just pull the nvitems from the phone and use them as they are or do i need to unlock them so that they are readable 1st?

[rich hathaway]

there is the definitions for those 4 items.why dont you tell me what you are trying to do,other than read those items,flash or what,maybe i can help you.
and no you shouldn't have to unlock anything except the spc to have access to them,only on a few phones are the profiles and such not accessible thru the nv

465^"Data Services Mobile IP General User Profile"^"Data*"
466^"Data Services Mobile IP Shared Secret User Profile"^"Data*"
1192^"HDR Access Network Stream CHAP Authentication Password"^"Data*"
1194^"HDR Access Network Stream CHAP Authentication User ID"^"Data*"

[whyrless]

THanks again Rich for the response, Im trying to use the Boost Mobile LG Venice as a ..... phone. I can connect to it and everything but i cant read the aaa password

also i forgot to mention that when i pulled the nvitems 466 and 1192 they show as access denied? Sum1 said i needed lgnpst and the dll to unlock them but i guess not?

[rich hathaway]

have you tried writing them? some you can write but not read.anyway i havent had that one before,but i just bought one off ebay a few mins ago,so if you cant get it figured out ill make a full flash for it a day or 2 after i get it.

[whyrless]

LOL, u know Rich, I honestly don't think i've ever tried to just write them on, ill do that now and report back.

Edit: that didnt work..it says 0 nvitems written

[rich hathaway]

got it this morning,got it full flashed this afternoon :) you can pm me for details,actually there is 2 ways you can flash this one

[whyrless]

Hey Rich did u ever figure out how 2 unlock the nvitems on the LG Venice?
thanks

[rich hathaway]

no i havnt picked it back up since last week.i will if i can find time before ctia.